|
|
High order numerical method in modelling and control systems
Veigend, Petr ; Horák, David (referee) ; Schirrer, Alexander (referee) ; Šátek, Václav (advisor)
Systémy pro řízení a regulaci jsou používány téměř ve všech průmyslových oblastech. Pro jejich modelování se často používají diferenciální rovnice, které popisují dynamické chování těchto systémů a umožňují je detailněji analyzovat z hlediska přesnosti, stability, výkonu a reakcí těchto systémů v reálném čase. V této oblasti se běžně nepoužívají metody vyšších řádů, protože vykonávají velké množství operací. Tato práce zkoumá numerické řešení obyčejných diferenciálních rovnic s použitím metody s proměnným řádem a proměnnou velikostí kroku, která je založena na Taylorově řadě. Metoda je navržena jak pro lineární, tak pro nelineární problémy a jsou implementovány její optimalizace pro snížení výpočetního času bez degradace jejích vlastností. Pozitivní vlastnosti metody jsou demonstrovány na sadě příkladů z technické praxe. Výsledky práce ukazují, že metoda založena na Taylorově řadě může být použita v oblasti řízení a regulace a má lepší vlastnosti než běžně používané metody.
|
|
|
MATLAB/Simulink, Real-Time simulation and control
Malík, Dalibor ; Chomát, Luděk (referee) ; Dvořáček, Martin (advisor)
This bachelor thesis provides information about a possibility of implementing the real-time, a serial line RS-232 and communication with a programmable controller (PLC) by Bernecker &Rainer (B & R) in MATLAB / Simulink evironment. Further, it provides information about options of creating a block in MATLAB / Simulink, modes of operation of the simulink and implementation of blocks to the blockset. In the proper communication with PLC the principle of PVI is described, the terminology connected with PVI is explained and setting and maintaining the communication between a source station and PLC is specified.
|
|
|
Design of special purpose tool for sag measurement
Mejzlík, Jiří ; Vetiška, Jan (referee) ; Houška, Pavel (advisor)
The aim of the thesis is to design a special purpose tool for sag measurement. Three possible solutions are proposed, for each the production cycle time is calculated and its approximate costs are estimated. The best solution in terms of a trade-off between both key quantities is suggested. Next part of the work deals with the selection of suitable drives for the manipulator as well as of the other components for the whole electrical device. Finally, a possible automated control of the complete machinery, including the electrical wiring diagram, is presented.
|
|
|
Technology Transfer Center
Kršková, Nikola ; Klimek, Karel (referee) ; Myslín, Jiří (advisor) ; Čuprová, Danuše (advisor)
This bachelor thesis is focused on a new building of office building in Telc within Technology transfer center. The shape of the land is trapezoidal and it is located in immediate proximity of the 1st class road, Třebíčská street. There are some others buildings of varios function near – college, administrative houses, houses of production, hall of residence. Its top view is rounded, defined by four ring arcs. The building is gaining mass with its height. It is situated on the northeast side of an estate, plot of land No. 5782/1. There is a car park in front of the building. There are a space laboratory for research and development of biological stuff, spaces for administration and management and biogas plant controling centre inside. The dominant space is an entrance hall with a staircase. The staircase is solved in Part D - architectural detail.
|
|
|
Peristaltic pump control via USB interface
Balogh, Jaroslav ; Chmelař, Milan (referee) ; Čech, Petr (advisor)
The purpose of this bachelor’s thesis is to practical realization of connection between peristaltic pump Rainin Dynamax RP-1 and PC, using USB interface. Integrated circuit device FT232R has been used in USB-RS422 converter, due to modified RS422 interface, which the pump RP-1 uses. There was also developed software for pump’s remote controll. RP-1’s functions can be driven from remote side or eventually automatized with this software. This work is based on semestral thesis and in future can be used in another aplications with RS422 or with RP-1 pump. Department of Biomedical Engineering, attached to FEEC, Brno University of Technology, will use this remote controll in analysis of DNA.
|
|
| |
|
|
Design of control system of pneumatic manipulator
Roun, Jiří ; Bradáč, František (referee) ; Vetiška, Jan (advisor)
This bachelor thesis is about the design of the control system for the pneumatic manipulator. Initial research describe the current possibilities of pneumatic products for driving and positioning of pneumatic assemblies. The practical part of this thesis describes the connection of hardware with PLC terminals and the design of software for controlling the manipulator. At the end of the thesis is testing part realized with designed software and measuring software.
|
|
|
Control modernization of two-axis manipulator
Mejzlík, Jiří ; Vetiška, Jan (referee) ; Houška, Pavel (advisor)
The bachelor thesis addresses the modernization of two-axis manipulator that is a part of the galvanizing line. The introductory section describes and evaluates the current situation and specifies the requirements for the device modernization. The selection of the proposed control is based on the analysis of possible solutions which are described in this work. The next part deals with the selection of suitable components and describes the process of implementation.
|
|
|
Control system for equipment using renewable energy sources
Novotný, Jan ; Bradáč, Zdeněk (referee) ; Benešl, Tomáš (advisor)
The work deals with design of power and control electronics for water micro source in island network. In the general part the readers are acquaints with the issue of renewable energy sources and describes commercially produced micro sources. The practical part deals with the design of its own control system and power electronics using its own control system or PLC for water micro source. The microcontrollers were used for the implementation of the control system, for which the program part was created.
|
|
|
Laboratory device with temperature control
Telecký, Jakub ; Škrabánek, Pavel (referee) ; Němec, Zdeněk (advisor)
This work deals with regulation and procedures that can be used for this. The theoretical part therefore presents the basic concepts of automation and controllers. The main part is the practical part. The purchased system consists of a regulated system, which must be set up correctly. Using system identification and known procedures, sample examples of how to best set the controller are compiled. The result is a sample laboratory task that automation students can try and gain experience with methods of setting up the controller.
|
guest ::
